Please keep
in mind that we are only going to sell you parts that you
specifically approved of, and we will try to supply you with
your lift model parts breakdown if you want one so it will help you determine the
correct parts you may need.
You
will get no hidden fees or charges, the price you see is the price you pay
when you purchase an item here that says "Delivered". Every
item on our website that you can click and pay for is marked
"Delivered" so you don't have to worry about an added on fee for
shipping duringcheck-out
time. Many items offer an additional 2% off if purchased by check instead of
processing a credit card. We pass the savings to you, and that can
be quite a bit if you plan on purchasing several lifts or air compressor or multiple
parts & accessory items.
Free
UPS Ground Shipping To Lower 48 States. Contact Us For Alaska, Hawaii, Puerto
Rico & Canada Shipping 1-630-678-9010 Note: UPS will not ship to P.O. Boxes
(Overnight Shipping Available Too, Contact us For Overnight Shipping Quotes.)
Hydraulic
Lift Oil
Premium
Quality Grade 32 Non-Foaming
Hydraulic
Oil For In-Ground Lifts & Surface Mount Lift Power Units
5
Gallons $115.00 Delivered
URGENT
SERVICE ANNOUNCEMENT! ALL
BENWIL single cylinder surface
lift models! That only use chain
or cables to lift one side in the master/slave
configuration,
need to be inspected regularly and right away.
Not very long ago, a
badly corroded chain failed causing a vehicle to fall. The lift did not have
properly operating locks and was missing at least one adapter. This failure
could have been prevented if the lift was properly maintained... A new
chain was installed and the missing lock components replaced.
If you own
this type of lift, make sure to inspect it or have it inspected immediately,
and if there is any sign of chain
(or cable) wear or improper operating locks,
please stop using
it until it is repaired properly. Smitty
Snap-On Issues Wire Rope Safety Advisory According to a product safety advisory issued by the Snap-On corporation, 4-post lifts manufactured between November 2005 and May 2009 experience premature wear of lifting cables. The June 2009 announcement explains that wire rope of inconsistent quality was used in 2005 to 2009 time period. This advisory further emphasizes its importance by stating “Failure of a wire rope could cause lift to collapse resulting in serious personal injury or death.” The Snap-On corporation warns that all 4-post lifts under the Wheeltronics, John Bean, Accu Ind, Snap-On,
Hofmann, Henessey, Mazda ESQ, and American Tire Distributors brands are subject to the safety advisory.
Order
this Rotary Original Equipment Version of the FJ7664 so your 90 day
Rotary Warranty Applies
$889.00 Each Delivered
Rotary Models SPO/SPOA9-300
or -400 and SPOA10-500 or -700
Cylinder
N380 or
N342 68" stroke Replacement Cylinder
$
689.00 Delivered
One cylinder
CALL US FOR CYLINDERS
FOR OTHER ROTARY
LIFTS
,
HAVE THE MODEL NUMBER READY
630-678-9010
NOTE!
HIGH-PRESSURE SEAL KITS ARE NOT RETURNABLE IF THE
PACKAGE HAS BEEN OPENED
Surface Lift Hydro Cylinders
MORE
Replacement
Seal Kits For Rotary Surface Lift Cylinders Here LINK
Seal kit for Rotary FJ7664, FJ7311,
FJ783 and FJ7211 cylinder with "Pacoma" or "MF" (Massey-Ferguson)
on
outside casing.
FJ783-12MF
/
7511-10
$79.00 Delivered
(kit
does one cylinder)
NOTE!
HIGH-PRESSURE SEAL KITS ARE NOT RETURNABLE IF THE
PACKAGE HAS BEEN OPENED
Seal kit for Rotary FJ7664
,
FJ7311, FJ783 and
FJ7211 cylinder with "TX" or "TH" or Texas
Hydraulics on
outside of cylinder casing.
FJ783-12TH
/ 7511-11
$89.00 Delivered
(kit
does one cylinder)
Universal seal kit that
will fit either of the above if you just don't know what brand cylinder
it is it is.
$124.00 Delivered
Universal Kit for one cylinder
7511-10U
Seal kit for Rotary
N380 or
N342 cylinder
$89.00 Delivered
(N342-12
Kit)
(kit
does one cylinder)
MORE
Replacement
Seal Kits For Rotary Surface Lift Cylinders Here LINK
NOTE!
HIGH-PRESSURE SEAL KITS ARE NOT RETURNABLE IF THE
PACKAGE HAS BEEN OPENED
& Replacement Seal Kits
For Surface Mount & High Pressure In-Ground Lifts
Available!
Replacements For All Brands Of Lifts.
(Brand Name And Model
Number Of Lift Needed)
MORE
Replacement
Seal Kits For Rotary Surface Lift Cylinders Here LINK
Contact
Us For Info...
Call
630-678-9060 between
9:00 AM & 5:00 PM (Central Time)
Mon. thru Fri. NOTE:
If you get the "phone lines are busy" message, or we are out of the
office and you get our answering machine, please be patient and leave a
message anyway and
Cover
Gaskets, Piston Bearings, Air Cylinders, Coil Air Hoses, Safety Latch Parts, Hydro
Cylinders, Hydro Hoses, Pumps, Cassette Water
Evacuation Pumping Systems.
Call
with the Rotary Model Number for accurate parts quote
Call for
Challenger and other Brand "High-Pressure Cassette Lift" Parts
630-678-9010
NOTE!
Now you can automatically evacuate the water from your cassette style in-ground
lift to help avoid corrosion and premature parts wear. LINK
"Smart Lift" Grease
T140208
Specially
formulated for Rotary Smart Lifts. Helps protect the operation of Rotary In-Ground
Lifts. Use with a hand grease gun to grease the cylinder sleeve guide bearings to protect your warranty and keep
your Lift working smoothly. Never grease
Rotary Smart Lifts with your air operated grease gun using regular chassis
grease. Too much pressure applied too fast, can damage or "pop"
the internal plastic grease tubing (that the grease flows through to each
bearing) causing "zero" grease to reach the bearings at all.
These cartridges
allow multiple grease applications from each single tube.
Rotary
Grease $29.00 Delivered
Two Cartridges
With Easy To Follow "Do-It-Yourself "
Installation Instructions
20-inch
Floor
Protector. Slotted to press onto ramp, can be trimmed shorter for narrower
ramps! (Bolts not Included)
For
Rotary & Other Compatible Lifts
$55.00
for set of TWO Delivered
Rotary Original Ramp
Slides (Yellow Color)
(They
seem to last longer than the copy's do)
$35.00
for ONE Delivered
$67.00
for set of TWO Delivered
Rotary
2-POST Equalizer
Cable Sheaves
Rotary
9k and 10k Capacity Lifts
SPO
or SPOA 7/9/10
SPO
or SPOA 84/88/94/98
Includes
"Retaining Clips"
FJ7116-1
is 3-1/2" Diameter X 3/4
thick with 3/4" Diameter hole
Grooved
opening for 1/4 inch cable
FOUR
Sheaves $49.00 Delivered
Sheave
Shaft for ALL 2-Post Rotary Lifts
10K Capacity & Under
$28.00
Delivered
Complete with shafts and clips
ROTARY
KIT FOR ALL 2-POST LIFTS 10K & UNDER
4 - Sheaves
2 - FJ7444-8 Shafts
4 - Clips for 3/4" shaft
Replaces all sheaves in overhead beam on 10K capacity and under.
$96.00
Delivered
Two
N377 Cable Sheaves
for ROTARY
2-Post 10K Lifts
Retaining
Clips included
$29.00 Delivered
Four
N377 Cable Sheaves with retaining clips
For
Rotary InBay 10K Lifts
$49.00
Delivered
One
Cable Sheave N417-1 for ROTARY SPO12 & S12i
ONE
STEEL Sheave $39.00 Delivered
Pulley
FJ7823-3 for SPO15 & SPO18
ONE
STEEL Sheave $59.00
Delivered
Sheave
Shaft SPO15 & SPO18
GENUINE Rotary Safety Latch
Cable
& Clamp
SAFETY
LATCH CABLE
29' long FJ7595-1/7501-24
INCLUDES CABLE CLAMP TOO, Fits ALL
Rotary 2 Post Lifts & many other brands using cable operated latches.
Too
Long? Cut The Excess Off! $38.00
Delivered
Rotary
29 foot Latch cable
Rotary
2-Post Safety Latch Cable Guides
TWO
(2)
guides $23.00 Delivered
ROTARY Overhead
Crossbeam Assembly
For ALL Rotary 2-Post Lifts 10K & Under
Complete
assembly includes R and L sides,
Four
cable
sheaves with axles
and over-height switch
bar complete
$389.00
Delivered N480N481N415 BLUE
COLORN480N481N415
RED COLOR
Call
630-678-9010 for other Rotary Models
Air Lock Release
Valves
(2-Way)
For
Older Model Rotary Surface Mount Lifts
Common air valve used on
many older Rotary 2-post lifts
1/4 X 1/4 "press-in" hose
couplers
This valve
only applies pressure, does not exhaust pressure. Older Model Lifts had Air
Cylinders That Slowly Leaked Air From The System.
This
will not take the place of the 3-way style pressure/exhaust valve used
on Newer Rotary Lifts. (FOUND BELOW)
Your
cost only $39.00 DELIVERED
Toggle Style Air Valve
Air Lock Release
Valves (3-Way)
For
Rotary Surface Mount Lifts. Commonly used air valve
on some Rotary 2 or 4-post lifts.
1/4 X 1/4 "press-in" hose
couplers.
(Usual
Rotary List Price Over $100.00)
Applies then releases
(exhausts) pressure
when handle
or
button is released
Only
$49.00
Delivered
Toggle
Style Air ValvePush
Button Style Air Valve
Rotary
Lock Release 3-Way Air valve
Fits all Smart-Lifts & 4-Post Rotary lifts
Heavy
Duty Made to Last & Last!
Applies then releases pressure when handle is released.
(Not
for a Rolling Jack)
For
Rotary
4-Post & Smart Lifts
65.00
Delivered
Air
Valve Including Hardware Kit Shown Below$98.50
Delivered
Hardware
Kit for ABOVE Air Valve
Includes
2 hose connectors, 1 Air Muffler, 1 Plastic Knob. Used
when converting old
style air valves to the new style valve above.
$39.00
Delivered
ROTARY
ARM RESTRAINT GEAR REPAIR KIT
Raise
Any Vehicle Lift 3 Feet High With No Vehicle On It And Push On The
Arms Actually Trying To Move Them... They shouldn't
swing AT ALL. If they
move, you should repair the arm restraint mechanism. If a vehicle should
fall off one adapter (or if a adapter fails) the only thing that helps stop
the momentum of the vehicle are the other arms & adapters helping to
hold it
in position.
ROTARY
ARM RESTRAINT
GEAR REPAIR KIT
Note: One Kit
Repairs One Arm Restraint Mechanism
CLICK TO ENLARGE IMAGE
Standard Restraint Gear Kit
SPO/SPOA7-100
$64.50 Delivered
Standard Restraint Gear
Kit
SPO/SPOA7-200
& SPO/SPOA9-200
$64.50 Delivered
Try the
"ADJUSTABLE" Restraint Kit Below, For Sagging Arms That Are Worn Slightly Causing
Gear Binding And Inoperative Locking
ADJUSTABLE Restraint Kit
SPO/SPOA7-100
$74.50 Delivered
ADJUSTABLE Restraint Kit
SPO/SPOA7-200
& SPO/SPOA9-200
$74.50 Delivered
As surface mounted Rotary lift arms wear over time, the swing arm pivot holes
in the carriage will become elongated, which
then causes the engaging gear to be forced inward against the arm restraint's main
gear. This results in improper alignment, excessive wear and disables the arm restraint system from being able to
engage properly.
To correct the problem you can replace the carriages, arm pins and swing arms at great expense or simply use
the low cost adjustable arm restraint gear kit shown above.
With the adjustable gear you can precisely position the gear to
achieve the proper fit before tightening the gear up, making the arm restraint system
able to engage again.
"Telescopic Style" Arm Restraints
are
available for
older Rotary models.
Call us with your lift model number
to get those
parts you want... 630-678-9010
Call
between 9:00AM & 5:00PM (Central Time)
Mon. thru Fri. NOTE: If
you get the "phone lines are busy" message, or we are out of the
office and you get our answering machine, please be patient, leave a message
anyway and we'll get back to you ASAP.
Available for all lifts, if you can't find them on this
LINK
just give us a call with the lift
brand name and your lifting requirements.
ROTARY
Lift Arm Pins
For SPOA/SPO82 & SPOA/SPO98
1-1/2" dia. X 8" long
2
Arm Pins $48.00 Delivered
For
SPO/SPOA7 & SPO/SPOA9
1-1/2" dia. X 8" long
2
Arm Pins $48.00 Delivered
For
SPO/SPOA10
2
Arm Pins $119.00 DeliveredContact
Us For Info...
Call
630-678-9010 between
9:00 AM & 5:00 PM (Central Time)
Mon. thru Fri. NOTE:
If you get the "phone lines are busy" message, or we are out of the
office and you get our answering machine, please be patient and
leave a
message anyway and
we'll get back to you ASAP to help you out.
LIFT
EQUALIZER AND LIFTING
CHAIN
AVAILABLE
Contact us and specify the
"pitch" if it's a roller type chain.
Contact
us and tell us the pitch and leaf chain lacing, whether it's 3X4, 4X4, etc. and we'll
give you a quote on the
quantity you need.
Slack
cable latch parts, pins, springs and other essential parts available! Make sure
your lift is safe to use by replacing worn latches before it jumps up & bites
you right in the ass someday.
Twinkie
Says "Safety First!"
ROLLING
JACK WHEEL
KITS FOR ROTARY JACKS
Find
the kit that fits your Rotary Rolling Jack
Very Hard Rubber Composite
Specifically
for R
OTARY Rolling Jacks that use this wheel
type
Same as Rotary SB100005 but includes axles and hardware.
Replaces
wheels on
one side of ROTARY Rolling Jacks that use this type hard rubber wheel.
$59.00
Delivered
Assembly
Has Steel Wheels & Support Springs
AXLE ROLLER KIT
Set of Four w/Springs Replaces ALL wheels on one rolling jack using this style
wheel assembly
$98.00
Delivered
Steel
Wheel Kit
for Rotary Rolling Jack
WHEEL KIT Completely Rebuilds One Side of a Rotary Rolling Jack, using
this type of steel wheel.
$
159.00
Delivered
For
all Rotary SPO & SPOA 7, 9, 10, 12 Models
FJ7360
Cup
Style Slider Blocks
8
Blocks (does one carriage) $155.00 Delivered
16
Blocks (does two carriages) $288.00 Delivered
CHECK
YOUR CABLE LENGTH, MEASURE FROM TIP TO TIP
SPO82
Standard Height Cables FJ7450
30ft 5-7/16" =
$79.00 Each Delivered
SPOA82
Standard Height Cables FJ7449 29ft
8-13/16" =
$79.00 Each Delivered
Two FJ7449 Cables $145.00 Each Delivered
SPO84
Standard Height Cables FJ7101
32'-3-9/16" =
$79.00 Each Delivered
SPOA84
Standard Height Cables FJ7156 & FJ7157 = $145.00 Set Of 2 Cables
IMPORTANT
NOTE: This model lift has two different length cables on it.
SP94
Standard Height Cables = Call
SPO94
Standard Height Cables = Call
SP88
Standard Height Cables = Call
SPO88
Standard Height Cables FJ7450
30'- 5-7/16" =
$79.00 Each Delivered
SPO88
EH1 Extended Height Cables
= Call
SPO88EH2 Extended Height Cables
= Call
SP98
Standard Height Cable Length FJ7421 25'-10-1/2" =
$79.00 Each Delivered
SPO98
Standard Height Cables FJ7450
30'- 5-7/16" = $79.00 Each Delivered
Two FJ7450 Cables $145.00 Each Delivered
SPO98EH2 Two Foot Extended Height
Lift Equalizer Cables
= Call
SPOA98
Standard Height Cables FJ7490 28'-10-11/16' = $79.00 Each Delivered
Two FJ7490 Cables $145.00 Each Delivered
SPOA98
EH1
One Foot Extended Height FJ7544 30'-10-11/16' = $79.00 Each Delivered
SPOA98
EH2
Two Foot Extended Height FJ7527 32'-10-11/16' = $89.00 Each Delivered
CHECK
YOUR CABLE LENGTH, MEASURE FROM TIP TO TIP
CALL
FOR ANY CABLES NOT LISTED HERE 630-678-9010
SPO7
Standard Height Cables FJ7450
30'- 5-7/16" = $79.00 Each Delivered
Two FJ7450 Cables $145.00 Each Delivered
SPO7
EH1
One Foot Extended Height FJ7547
32'- 5-7/16" = $79.00 Each Delivered
SPO7
EH2 Two Foot Extended Height FJ7528
34'- 5-7/16" = $89.00 Each Delivered
SPOA7
Standard Height Cables FJ7449
29'- 8-13/16"
=$79.00 Each Delivered
Two FJ7449 Cables $145.00 Each Delivered
SPOA7
EH1
One Foot Extended Height FJ7545 31'-
8-13/16"
=$85.00 Each Delivered
SPOA7
EH2
Two Foot Extended Height FJ7546 33'-
8-13/16"
=$89.00 Each Delivered
SPO9
Standard Height Cables FJ7450 30'- 5-7/16" = $79.00 Each Delivered
Two FJ7450 Cables for SPO9 $145.00 Each Delivered
SPO9
EH1
One Foot Extended Height FJ7547 32'-5-7/16 = $79.00 Each Delivered
SPO9
EH2
Two Foot Extended Height FJ7528 34'-5-7/16 = $89.00 Each Delivered
SPOA9
Pre 100 SERIES LIFT (Means there is no "SPOA9-100" or higher number
after the SPOA9
Standard Height Cables FJ7840 29'-2-3/4" =
$7.00 Each Delivered
SPOA9
EH1Pre 100 SERIES LIFT
One Foot Extended Height FJ7841 31'- 2-3/4" = $75.00 Each Delivered
SPOA9
EH2Pre 100 SERIES LIFT
Two Foot Extended Height FJ7842 33'- 2-3/4" = $79.00 Each Delivered
SPOA9
Standard Height Cables N33 30'- 2-3/4' = $79.00 Each Delivered One
N33 Cable
Two N33 Cables for
SPOA9 $145.00 Delivered Two
N33 Cables
SPOA9
EH1
One Foot Extended Height N34 32'- 2-3/4' = $79.00 Each Delivered
Two
N34 Cables for
SPOA9 EH1 $145.00 Delivered
SPOA9
EH2
Two Foot Extended Height N35 34'-2-3/4' = $85.00 Each Delivered
Two
N35 Cables for
SPOA9 EH2 $160.00 Delivered
SPO10
Standard Height Cables N374 30'- 3-13/16" =$79.00 Each Delivered
SPO10
EH1 One Foot Extended Height N379
32'- 3-13/16" =$79.00 Each Delivered
SPO10
EH2 Two Foot Extended Height N375
34'- 3-13/16" =$79.00 each Delivered
SPO10
EH4 Four Foot Extended Height N376
38'- 3-13/16" =$89.00 Each Delivered
SPOA10
Standard Height Cables N372 30'-1/2 = $79.00 Each Delivered
SPOA10
EH1
One Foot Extended Height N378 32'-1/2 = $79.00 Each Delivered
SPOA10
EH2
Two Foot Extended Height N373 34'-1/2 = $79.00 Each Delivered
SPO12
Standard Height Cables
33'- 6-7/8" = $98.00
Each Delivered
N387
SPO15 & SPO18 Standard Height Cables
39'-4" = $98.00
Each Delivered
CALL
FOR ANY CABLES NOT LISTED 630-678-9010
CHECK
YOUR CABLE LENGTH, MEASURE FROM TIP TO TIP
Call
for Rotary 4-Post Lift Cables 630-678-9010
For any brand surface
mount lift available, just call us
630-678-9010
with make and model
or if you don't know the model number give us the
total length
of cable measured from "Tip to Tip"
the diameter of the wire rope (1/4, 3/8, 1/2, etc) and the thread
size.
We can provide custom made cables for obsolete lifts or for
lifts with hard to find
or too expensive OEM cable prices.
We have sheaves,
pins, shafts, bushings and
other replacement
parts too, call or leave a message at 630-678-9010
"Delivered"
= FREE SHIPPING!
Is
Your Lift Chattering?
Help stop
the problem by adding "Metholardate"
to the oil.
Oil Additive
Metholardate adds lubricity
to the hydraulic oil and "Sticks" to the internal metal surfaces
protecting them. New seals tend to provide more sealing surface which can
cause the lift to hang-up on the way down, especially if it doesn't have a
load on it.
It is recommended
for Surface Lift Cylinders and In-Ground Cylinders or anytime the lift is chattering.
5502300 Hydraulic
Cylinder 69 inch stroke 2 In diameter piston
$469.00
Delivered
BendPak
Equalizer Cables
You
should measure your existing cables to make sure the length is the same as
the cables you are ordering. BendPak changed some lift models and it's better to
check the length of the cables.
(Measuring them could save you the cost of
shipping them back & a restocking fee.)
MX10C
uses two 350" cables
(Check
measurement to be sure of length you need)
350
inch 5595490 $95.00 Each Delivered
MX10AC
uses two different length cables
(Check
measurement to be sure of length you need)
347
Inch 5595500 $95.00 Each Delivered
350
inch 5595490 $95.00 Each Delivered
MX10ACX
uses two different length cables
(Check
measurement to be sure of length you need)
360
Inch 5595510 $95.00 Each Delivered
363
inch 5595515 $95.00 Each Delivered
MX10CX
uses two 363" cables
(Check
measurement to be sure of length you need)
363
inch 5595515 $95.00 Each Delivered
XL9
uses two 345" cables
(Check
measurement to be sure of length you need)
345
inch 5595209 $95.00 Each Delivered
XL9X
uses two 358" cables
(Check
measurement to be sure of length you need and diameter is 3/8)
3/8
inch 5595210 $95.00 Each Delivered
Pulley
for BendPak Lift Model XL9 and Other Model Lifts
(Check
the measurements when using on other models)
Solid
Steel Pulley, 3 inch diameter, 5/8 inch wide with a 3/4 inch diameter
bushing hole
Part
# 5575310
SET
of TWO $37.00 Delivered
One 5575310 Pulley $25.00 Delivered
Call
to place order and for other model BendPak Cables 630-678-9010
Chain Rollers
Replace the original
"bushing style" rollers with
high quality Rollers with SHIELDED ROLLER BEARINGS.
One
2.5 Inch Diameter Roller with 3/4 inch Shaft Hole
$89.00
Delivered
One
4 Inch Diameter Roller with 3/4 inch Shaft Hole
Need
A "Cable Pull
Type" Over-Height Unit? $479.00 Delivered CLICK
THIS LINK
If
you have a Forward Lift or other brand that has a "thin cable operated
over-height limit mechanism" you may want the unit at thisLINKIt has a built in limit switch that
the cable pulls to kill the power.
Or
maybe
a 3-Phase power unit with a bigger tank for a 4-Post Lift?
SPX
FENNER FLUID POWER... THE BEST, MOST RELIABLE POWER UNIT ON THE MARKET!
Order
by 3:00 PM "Central Time" 630-678-9010
ships-out same-day
(Free
UPS Ground Shipping To 48 Continental States, call for
Alaska, Hawaii & Puerto Rico Shipping)
FREE
SHIPPING!
Always In-Stock - Ships Out
Same Day - Mon-Fri
SALE $40.00 OFF
Sale
$499.00$459.00
SPX
Fenner Single phase 220V Power Unit with 4 Gallon Tank
Weight
- 51 pounds Ships UPS Ground - Free Shipping to 48
Contiguous States
One
Full Year Manufacturer's Warranty
(NOTE:
Local Chicago Area "Will-Call" Price $4
59.00
Tax Paid! Your total cost $459.00)
Same
Power Unit with OverHead LIMIT SWITCH $499.00 Delivered LINK
Still
Looking
For A Better Deal? Well here it is!
New
Power Unit
(Above) Plus,
Smitty's Premium Hydro Oil To
Fill It!
You
get the power unit shown above and a 5 Gallon Pail of
Premium Hydro Oil.
That's
enough to fill the tank and have a
gallon left over to top off your other lifts
or
other equipment that calls for Grade 32 hydro Oil.
Only
$539.00 Delivered Always In Stock
This
single phase 220v power unit can be adapted
to ANY 2-POST vehicle lift that had the same
or different brand power unit originally mounted on
column side or column top.
NOT for lifts that are controlled
by a keypad, this power unit is operated directly from
the power unit itself.
(The removable plastic plug next to the lowering valve is the pressure hook-up
point.)
Maintainable
for many years because repair parts are always available
unlike some other brands that are
actually considered disposable.
IMPORTANT!
When ordering a power unit, please check the motor
on your old power unit and make sure you are
ordering the correct phase motor. This is a single
phase power unit.
We are not responsible for the
wrong phase power unit being ordered.
Works
On 4-Post Lift If 4-Gallon Oil Tank Required.
Optional
Higher Pressure RV18 Relief Valve Available for
additional $69.00 delivered
Other
fixed relief pressure valves also available -
630-678-9010
Warning:
Do not exceed the lifting capacity rating of the
lift
Manufacturers
Warranty
On All SPX Power Units - 1 Year Parts. Note:
Warranties are processed at SPX Fenner in Rockford IL, their inspection of the
power unit determines the warranty refund or repair. It is the responsibility of
the end user of the unit to ship the power unit in if it can't be repaired
easily right on the worksite by the end user with SPX supplied repair
parts.
"O"
Ring & Seal Kit Revitalizes Your SPX Fenner Power Unit
If
your power unit is losing pressure and has difficulty lifting vehicles
like it used to,
you may need to replace the internal pump seals...
Worn
leaky seals between the pump and valve body inside the power unit tank, allow
the oil from the pump to squeeze past and return to the tank instead of
filling the hydraulic cylinders. Worn "O" rings between the pump and
suction tube allows air into the system and can also cause the pump to lose
it's "prime" and take longer to build pressure before it begins to
raise the load... Several special seals and "O" rings are included
in this pump seal replacement kit. Installing the parts from this kit takes
about a half an hour, and even a Monkey could probably do it if you bribe it
with a banana or two! No oil draining necessary because it just stays in
the tank when you lower it.
Pump "O" ring
& seal kit for ALL SPX Fenner Auto Lift Power Units
Sale
$29.00
Each Delivered
7006-25
K-40
Seal Kit
Pump Seal Kit Available for Rotary/Forward Global Power Units Too
LINK
Or
maybe a
3-Phase
power unit with a bigger tank for a 4-Post Lift?
You
will get no hidden fees or charges, the price you see is the price you pay
when you purchase an item here that says "Delivered". Every
item on our website that you can click and pay for is marked
"Delivered" so you
don't have to worry about an added on fee for
shipping during
check-out
time. Many items offer an additional 2% off if purchased by check instead of
processing a credit card.
We pass the savings to you, and that can
be quite a bit if you plan on purchasing several lifts
or air compressor or
multiple parts & accessory items.
Free
UPS Ground Shipping To Lower 48 States. Contact Us For Alaska, Hawaii, Puerto
Rico, Canada & Mexico Shipping.
Note: UPS will not ship to P.O. Boxes
(Overnight Shipping Available Too, Contact us For Overnight Shipping Quotes.)
Lift
Relocation/Re-Installation Kit
s
Available
for any model lift!
Lift
Relocation/Re-Installation Kit
Buy
a Used Lift you need to Install? Or just relocating an existing lift?
70.00
Delivered Sometimes
used on 2-post lifts with
NO shims under column
20
Anchor Bolts 3/4
inch X 5-1/2 in. long
Zinc Plated Steelwith
washers and nuts
$75.00
Delivered
Usually
used on 2-post lifts
20
Anchor Bolts 3/4
inch X
7
in.
long
Zinc Plated Steel
with
washers and nuts
$
98.00
Delivered
Usually
used on 2-post lifts with
shims
under column
20
Anchor Bolts 3/4
inch X
8-1/2 in.
long
Zinc Plated Steel
with
washers and nuts
$
105.00
Delivered
Sometimes
used on 2-post lifts with shims
under column
20
Anchor Bolts 5/8
inch X 4-1/2 in. long
Zinc Plated Steel with
washers and nuts $69.00
Delivered4-1/2
inch long
20
Anchor Bolts 5/8
inch X 5 in. long
Zinc Plated Steel with
washers and nuts $
69.00
Delivered
5 inch long
20
Anchor Bolts 5/8
inch X 6 in. long
Zinc Plated Steel with
washers and nuts $69.00
Delivered
6 inch long
20
Anchor Bolts 5/8
inch X
8-1/2 in.
long
Zinc Plated Steel with
washers and nuts $95.00
Delivered8-1/2 inch
long
Column Leveling Shims
For Leveling
Lift Columns During Installation
75
piece assorted
plastic "U" shims
25
each of the following thickness sizes 1/16, 1/8 & 1/4
inch.
$40.00 Delivered
150
piece assorted
plastic "U" shims
5
0
each of the following thickness sizes 1/16, 1/8 & 1/4
inch.
Usually
enough level several lifts and have a few left over.
$69.00 Delivered
ROTARY
Leveling Plates
2-Post
Shim Plate Kit provides one inch of plates
For Rotary
SPO/SPOA7, SPO/SPOA9, SPO/SPOA10
(Same as Rotary FA5112 kit)
Includes
two of the 1/4" thick plates &
four of the 1/16" thick
plates
$
215.00
Per Kit Delivered!
Contact
us about steel shim plate kits for Challenger and other lifts!
Rotary
Original Wheel Spotting Dish Kit
For mounting on floor to use as
a gauge where to spot vehicles prior to raising on
lift. Floor mounting pins included. Vehicles can use 3 positions, one in front of
the dish, one on the dish and one behind the dish
depending on the length of the vehicle.
Each FF729 Kit
$39.00 Delivered
Two for
$69.00 Delivered
SIZE of spotting
dish 12 inches wide X 10-1/2 inches
Mounting Hardware Included
One
$39.00 Delivered
Two dishes $69.00 Delivered
EXTRA
WIDE Spotting Dish
15" X 10-3/4"
Like
Above, but WIDER you can see it easier out the door while spotting vehicle.
Narrower cars fit it
too while centered on the lift.
No name on it, well made
thick HD gauge steel, painted yellow.
Includes
Mounting Hardware.
SIZE of spotting
dish 15 inches wide X 10-3/4 inches
Wide Spotting Dish
$39.00
One
Dish
TWO
Wide Spotting Dishes for $69.00
Dual Spotting Dish
Longer
Dish used for auto, truck and longer vehicle spotting.
Extra
Wide!
$58.00 Each Delivered
20-1/8
inches tall X 15 inches wide!
Great
for spotting long or short vehicles on a lift!
Steel
Dual Turntable Kits
Measurements are 13-1/4 inches X 14
inches.
Black painted steel
1.5 Ton capacity each
Two turntables 116 pounds shipping
weight
Set of Two $579.00
Delivered
Same style like above, with a 14-3/4 X
14 inch measurement
Set of Two $629.00
Delivered
NEW
Style! Stainless Steel Turntable
otherwise like above set 14-3/4 X
14 inch measurement
Set of Two
$798.00
Delivered
SLIP PLATE REPLACEMENT BALLS
AVAILABLE!
Hey!
Been Losing Yer Balls Lately
From
Your Alignment Rack's Turntables or Slip Plates?
Now you can
just replace them when they get busted or worn out...
Sold
in quantities of 30 per order...
Will work on any brand turntable with replaceable
ball bearings.
This
system mounts to the inside frame of the cassette lift and includes everything
you need to install it as instructed. Every time you operate the lift, water
is pumped out of the containment tub!
Aqua-Out 2 GPM kit
$329.00 Delivered
Aqua-Out 5 GPM kit
$368.00 Delivered
Ever since the first cassette style lifts were invented by the Europeans, moisture has been the one single biggest difficulty. This is because each time the lift is raised fresh air is drawn into the lift, replacing the void created by the rising plungers.
This air condenses once inside the lift and begins to accumulate. As the water accumulates and rises various components in the lift become submerged and begin to corrode.
This
corrosion can cause some problems to certain important elements of the
lift.
In just about two hours, you can put an end to water accumulation problems at
any site where a cassette lift is installed and moisture in it is a
problem.
The
Aqua-out unit is designed to fit most cassette style lifts produced by Rotary
Lift,
Challenger
lifts and other competitive makes as well. The standard unit uses a 2 GPM
pump, which will do the trick at most locations. However, where water really
accumulates quickly from floor cleaning, etc. you may want to upgrade to the 5
GPM version.
Once installed, you can run Aqua-out continuously to get the mass quantity of
water out. Once the water level is lowered, the Aqua-out system will
automatically remove water as it builds up each time the lift is lowered or
anytime the air valve is actuated.
The Aqua-out system is shipped with everything you need
& easy to follow instructions.
Challenger "Old
Style" Low-pressure In-ground lift Parts Click
Link
Overhead
Mercury Limit Switch
Fit's
on end of overhead limit bar so power unit shuts down when vehicle is too high
for lift and touches bar
Mercury
Switch with 12-1/2 Ft. length connecting wire $87.00
Delivered12045
Mercury
Switch with shorter 26 inch connecting wire $64.00
Delivered
Used
on Dual Pendant Control Challenger Lifts
Challenger
Lift "Height Adapters" and replacement rubber pads can be found
at this linkLINK
CARRIAGE
LOCK RELEASE CABLE REPLACEMENT KIT
FOR OLDER STYLE CHALLENGER & VBM LIFTS
(Others
sell the cable, link and hook separately, this kit has all three parts because
if the cable is broken or ready to break, the hook is probably partially worn
through and ready to snap too.)
One
for $35.00 Delivered 31150/51
TWO for
$65.00 Delivered 31150/51
Challenger
Newer Style Manual
Safety Latch Release Cable
For
Model 36000 - Cable #36029 $49.00 Delivered
For
Model 37000, 39000, 70000 Cable #37125 $58.00 Delivered
Latch
covers for older model Challenger and VBM lifts click this LINK
Challenger Lift Cylinder
Heavy Duty ROLLER & YOKE ASSEMBLY
Tube
Fits 1-3/4 Ram, Four inch diameter chain roller with Heavy Duty Shaft Bearings,
roller has 1-1/2 inch wide chain surface with 1/4 inch lip on each side to keep
chain on roller. This item sits on top of hydraulic cylinder ram and
raises carriage with lifting chain.
$239.00 Delivered
Challenger
Replacement
Hydraulic Cylinders
For
Challenger Surface Lift Model Numbers
20000
21000
26000
27000
28000
30000
31000
33000
35000
$459.00
Each Delivered!
Challenger #31265
For
Challenger Surface Lift Model Numbers
B2900
Ammco Lifts Too!
36000
37000
39000
12000
(2-post lift)
$479.00
Each Delivered!
Challenger #39097
For
Challenger Lift Model Numbers CL9, CL10, CS0920, CS1020(w) and CS1220
$469.00
Each Delivered!
Challenger #16138
For
Challenger Lift Model Number 15000 and 18000 2-post lifts
For
Challenger 2-post Models 12000, 37000, 39000 and Others
Valve has 1-1/2 inch wide plastic push button you
can screw onto valves metal push button. Three 1/8 NPT threaded ports for air
hook-up and exhaust. Valve body is 1-1/4 inches high, 1 inch wide and 1-1/4
inches deep.
Note: No mounting bracket is included with this
item.
Air
Control Valve - $79.00
Each Delivered
37016/7228-73
Complete valve assembly (like
above) but includes mounting bracket,
In-Ground
Low-Pressure Lifts that last & last & last...
Underground
tank spring a leak? Save that lift by using one of these to efficiently
replace the old tank by mounting it next to the wall and piping to the oil
valve to save a large underground installation bill.
Tanks
are 14 to 16 inches in diameter depending on the capacity.
Tanks
can
be buried under the shop floor or mounted on the floor surface near the 1-1/4 inch oil
valve that operates the lift.
Call
for price on Fiberglass Coated Tanks for installing it underground. 630-678-9010
Fore & Aft Style
Lift Tanks are also available
Tank Kit Includes:
Filler
Plug with Dipstick & Low
Oil Control Tank Float.
Certified
Tanks
36
Gallon Capacity Tank: 14-inch diameter X 58-inches tall
Used
for ALL single post 10-5/8 diameter hydraulic cylinders.
Tank
has 1-1/4 inch NPT oil pipe outlet on bottom and
1/2
inch NPT air pipe inlet on top.
9801C
weighs approximately 124 pounds
$769.00
Delivered
42
Gallon Capacity Tank: 16-inch diameter X 52-inches tall
Used
for ALL two post side by side with 8-1/2 inch
or
smaller diameter hydraulic cylinders.
Tank
has 1-1/4 inch NPT oil pipe outlet on bottom and
1/2
inch NPT air pipe inlet on top.
9802C
weighs approximately 125 pounds
$789.00
Delivered
47
Gallon Capacity Tank: 14-inch diameter X 74-inches tall
Used
on Fore & Aft lifts that call for this tank size
Tank
has 1-1/4 inch NPT oil pipe outlet on bottom and
1/2
inch NPT air pipe inlet on top.
9805C
weighs approximately 145 pounds
$1189.00
Delivered
62
Gallon Capacity Tank: 16-inch diameter X 75-inches tall
Used
on Fore & Aft lifts that call for this tank size
Tank
has 1-1/4 inch NPT oil pipe outlet on bottom and
1/2
inch NPT air pipe inlet on top.
9804C
weighs approximately 145 pounds
$1189.00
Delivered
Oil
Tank Plug & Dipstick - 1-1/2 inch Diameter (NPT)
Thread
$59.00
each Delivered
Oil
Tank Plug & Dipstick - 2 inch Diameter
(NPT) Thread
$59.00
each Delivered
"Low Oil Control"
Tank
Float
For
ALL In-Ground
"Full Hydraulic" Lift Oil Tanks
Complete with
Metal "Hook" Eye
These
Floats are 100% Aluminum!
Replace your tank
float if you were using your lift while low on oil
causing the float to clang
against the bottom opening of the tank.
Replace it before the old float gets jammed in
the tanks bottom opening and you end up having a car stuck up in the air when
the float gets stuck and refuses to allow oil back into the tank.
$54.00 Delivered
IN-GROUND
LIFT
For Any Brand
Lift
1/2 Inch
NPT(F)
This is a picture of solid brass body Non-Locking
or Locking Style Valves
with 1/2 inch NPT Female Threads
NON-LOCKING STYLE AIR VALVE
(pictured above on the left)
ALL BRASS BODY
1/2 inch NPT Female Thread
The Non-Locking style air control valve is for
SINGLE-POST SEMI-HYDRAULIC LIFTS
that only have
ONE valve (the air valve shown)
that operates the lift.
FK-303-500 Non-Locking
Valve
$76.00
each Delivered
FK-303-500
Valve and 9640 Exhaust Muffler $96.00 Delivered
LOCKING
STYLE AIR VALVE
(pictured above at
right)
The
Locking style air control valve is for TWO-POST or SINGLE-POST
FULL-HYDRAULIC LIFTS
that have two
separate valves, an Air Valve and an Oil Control Valve to
operate the lift.
FK-302-500 Locking Valve
$76.00
each Delivered
FK-302-500
Valve and 9640 Exhaust Muffler $96.00 Delivered
LIFT
AIR
VALVE REPAIR KIT
PACKING
KIT FOR AIR VALVES SHOWN ABOVE
Completely
replaces packing, spring & "O" ring on
the
Intake and Exhaust sides of Air Valve (SHOWN
ABOVE)
$28.00
Delivered
LIFT
AIR
VALVE REPLACEMENT LEVERS
$25.00
Delivered
$25.00
Delivered
Air Exhaust Muffler
1/2 Male Pipe Thread Connection
Heavy Duty
Aluminum Construction
Quiets Down
Air Exhaust Noise
Muffler won't rust!
$34.00
Delivered
Our Quietest Muffler
Non-Rusting
Aluminum
1/2
NPT Male Pipe Thread
$28.00
Delivered 9642
In-Ground Lift 1-1/4 inch
NPT(F) Oil Control Valve
Replace that sticky, worn out,
leaky oil valve with a brand new one!
Horizontal
Valve Style
(Handle color may vary)
The
Original Dependable Oil Valve Used On "Full-Hydraulic" In-Ground Lifts!
Brass
1-1/4
Inch NPT(F) Valve
with Steel Handle
Replacement
External Spring
For 1-1/4 inch Oil Valve (above)
Includes Nylon Bushing
& Spring
$27.00 each
Delivered
In-Ground Lift 1-1/4 inch
NPT(F) Oil Control Valve
Vertically Mounted
Style
For
In-Ground Full Hydraulic Lifts
Brass
1-1/4
Inch NPT(F)
Valve with Steel Handle (Spring Loaded Return)
$219.00
each Delivered
Is
Your In-Ground Lift Chattering?
Help stop
the problem by adding "Metholardate"
to the oil.
Oil Additive
Metholardate adds lubricity
to the hydraulic oil
and "Sticks" to the internal metal
surfaces protecting them. New seals tend to provide more sealing surface which can
cause the lift to hang-up on the way down, especially if it doesn't have a
load on it.
It is recommended with every
in-ground lift seal change and anytime the lift is chattering
or sticking.
1 Qt. Can 9960-25 $33.00
Delivered
1 Gallon Can 9960-01 $89.00
Delivered
In-Ground
Lift Arm-Friction Washers
6
Inch Flat Disk Style with 3/4 Hole In Center
Non-Metallic
Plastic Fiber Arm Friction Disks. When GREASED and fit
between the lift arm and superstructure the arm swings more easily.
Set
of 4 Arm Disk/Bushings $55.00 Delivered
SEALS
for Rotary "Low-Pressure" In-ground Lifts
Complete with
easy to follow installation instructions
Kit
for
8-1/2 diameter Rotary Lift Cylinder With 6-bolt Aluminum Gland
Ring
Use a magnet to determine the type
of metal the gland ring is made of,
this kit is used with
a 6-bolt aluminum gland cylinder.
These kits directly
below are for ROTARY
brand Low-Pressure in-ground lifts
8-1/2"
DIAMETER SEAL KIT FOR LIFTS WITH
6-BOLT ALUMINUM GLAND RING.
This kit comes with new
(JG620 style) gland ring, (JG220 style) seal
& spring,
brass bleeder plug, new grade-8 bolts &
washers and installation instructions.
Seal
& Gland "COMBO KIT" 8-1/2 Inch
S-1721/21B
(J136)
$98.00
Delivered (No Shipping Fee Charged)
WANT
THE RUBBER SEAL ONLY from the kit above?
8-1/2 in.
Diameter (JG220) seal kit
for Rotary lifts with 6-bolt aluminum gland ring
$68.00
Delivered
Includes
seal & spring & install instructions (NO NEW
Gland ring,
Bolts or Bleeder Plug)
Rotary
Genuine Part Similar To "Combo Kit" (Image
Shown Above)
8-1/2 inch Combo Seal & Gland
Kit, with 6-bolt aluminum gland ring,
but doesn't include new grade-8 bolts, washers
or
bleeder plug.
Genuine
Rotary Part
$149.00 each
Delivered!
WANT
THE RUBBER SEAL ONLY from the Rotary J136 kit above?
Genuine Rotary Seal OEM Part
#JG220 (seal
& spring only)
$75.00 Delivered
Seals for
Low-Pressure ROTARY In-Ground Lifts
10-5/8
Diameter Combo Kit For Rotary Lift Cylinder
With
6-bolt Aluminum Gland Ring
10-5/8 INCH
DIAMETER SEAL KIT FOR LIFTS WITH 6-BOLT ALUMINUM GLAND RING
this kit comes with new (JK622 style) gland ring, (JK227 style) seal
& spring,
(JX207 style) brass bleeder plug, new grade-8
bolts & washers and installation instructions.
Use a magnet to determine the type
of metal the gland ring is made of,
this kit is used with
a 6-bolt aluminum gland cylinder.
Seal-Gland Combo-Kit 10-5/8 1799/99B
(J134)
10-5/8
Kit $105.00
Delivered
WANT
THE RUBBER SEAL ONLY from the
above 1799/99B kit?
10-5/8 in.
Diameter BH-1799 (JK227) seal kit
for Rotary lifts with 6 bolt aluminum gland ring
$67.00
Delivered
Includes
seal & spring & install instructions (NO NEW GLAND,
Bolts or Bleeder Plug)
Rotary
Genuine J134
Like above
1799/99B Combo kit but Rotary Original Part
J134 OEM 10-5/8 Combo Seal & Gland Kit,
like above combo kit
with 6 bolt aluminum gland, but without new grade 8 bolts or
bleeder plug.
Genuine
Rotary Part
$179.00 Delivered
WANT
THE RUBBER SEAL ONLY from the
above J134 Rotary kit?
Genuine Rotary Seal OEM Part
#JK227 (seal
& spring only)
$85.00 Delivered
SAVE THAT
Rotary 2-POST
Low-pressure In-ground Lift!
Wobbly
Shaky Pistons?
Changing
seals again & again and they're still leaking even when fairly new?
For Any 6-Bolt
Aluminum Type Gland "In-ground" Rotary Lift...
Cut-away shows new bearing surface
This Upper Bearing
& Seal Kit for
LOOSE Pistons Can Help Solve The Problem.
You can try this test...
While
lift has no vehicle on it, raise your lift until it tops out, then lower it about
an inch or two.
With the controls at "neutral" grab the
superstructure (where the arms attach) and try shaking it back and forth hard.
If the piston "wobbles" or has any "side to
side" movement, that means the top bearing is worn inside the hydraulic cylinder and a
small gap
is being created between the piston and
the seal allowing oil to
"burp" past.. Seals can flex a little to make up for some play in
the bearings, but if the bearing is too worn, even brand new seals can't
prevent oil from leaking past.
When a vehicle is on it
the same wobbling happens, but when you raise the lift all the way, the flange on
the bottom of the piston seats against the inner top of the cylinder and
holds the piston steady preventing the movement that allows oil to leak
past. Most of the leaking happens during the act of
wobbling,
while
raising
or lowering the lift, or if you only have it up part way like when doing a brake
job.
This bearing/seal replacement kit for Rotary 6-bolt Gland Rings adds a new upper bearing to your lifts
hydraulic cylinder effectively limiting the extra play from
old worn cylinder bearings. The kit also includes a new seal style, converting
the cylinder from the old style seal that had a spring on the bottom to the new JG227 Rotary Seal.
The new bearing is replaceable
too, allowing you the ability to maintain your older lift for years of added
service capability.
Helps
stop leaks due to
misaligned piston and can add YEARS of service to
your otherwise dependable Rotary
in-ground lift!
For
SIX Bolt Gland Rotary Cylinder Only
8-1/2 inch
Upper Bearing Gland & Seal Kit (JG629/9762-01)
Regular Sale Price
$449.00 DELIVERED!
One
Bearing Gland & Seal Repair Kit
Quantity
SALE Two 8-1/2
inch kits for $739.00 delivered
Two
Bearing Gland & Seal Repair Kits
ONE
"Adjust
- To - Fit" Version 8-1/2 bearing, gland & seal kit $498.00
Delivered
(Like
above, but has an adjustable bearing so you can fit the bearing better if
needed)
Adjust
- To - Fit Version 10-5/8 bearing, gland & seal kit $698.00
Delivered
ROTARY LIFT Seal Kit JG227
FOR
8-1/2 INCH DIAMETER
PISTON "BLUE SEAL" KIT SPECIFICALLY FOR
ROTARY LIFT WITH 8-BOLT STEEL GLAND RING.
Kit comes with seal and installation instructions. These seal kits
are installed without removal of the 8-bolt steel
gland,
just by turning the piston 90 deg. The piston drops down
far enough to pull the seal and replace it. They are also used on
some six bolt steel gland applications where you must
remove the gland completely to install them.
Bearings
on these 8-bolt cylinders can be replaced if needed by ordering
a bearing kit.
Look
below for more about the bearing replacement kits.
Genuine
Rotary Part
$56.00
each Delivered
Rotary
Original JG227 8-1/2 inch diameter Seal
Kit
Same
Kit, Only Supplied By Seal Company $49.00 Delivered BH-1706
10-5/8 INCH DIAMETER
SEAL JK238 SPECIFICALLY FOR
ROTARY LIFTS
WITH 8-BOLT STEEL GLAND RING.
Rotary
part JK238KIT Rotary
10-5/8 Seal Kit
"Bearing
& Seal Kit" for 8-Bolt Steel Gland Cylinders
Bearings
Worn On ROTARY 8-Bolt Steel Gland Cylinder?
Seals
leaking & Pistons Wobbling? or Binding Cylinder Movement?
ORIGINAL
ROTARY PARTS
Seal, "O" Ring
and Replacement Bearing Kit for 8-Bolt Rotary Steel Gland Type Cylinders.
If piston "wobbles" or seals seem to be leaking for no good reason,
you may need to replace the removable "Nylatron" bearings in the 8-bolt gland.
You can try this test... While
lift has no vehicle on it, raise your lift until it stops, then lower it about
an inch or two. With the controls at "neutral" grab the top of the superstructure
where the arms attach and try shaking it hard, if it "wobbles" or has
side to
side movement, that means the top bearing is worn inside the cylinder and a gap
is being created between the piston and the seal allowing oil to escape. When a vehicle is on it
the same thing happens, but when you raise the lift all the way, the flange on
the bottom of the piston seats against the inner bearing of the cylinder and
holds the piston steady.
Most of the leaking happens during the act of raising
or lowering the lift, or if you only
have it up part way like when doing a brake
job...
This kit comes complete with NEW seal, 2 bearings, 1 "O" ring,
bleeder plug and new bolts.
One Kit Does One (8-bolt Gland)
Cylinder
8-1/2 inch
seal / bearing / O-ring kit $87.00
Delivered JG227-30
10-5/8 inch
seal / bearing / O-ring kit $149.00
Delivered JK238-30
NEW
ROTARY LIFT ARMS
&
SUPERSTRUCTURES
SAVE THAT
Rotary 2-POST
Low-pressure In-ground Lift!
Fits
ROTARY In-Ground "DTO-28"
2-Post
Low-Pressure Lifts
(
DTO
Models have
8.5 Pistons and "I" Beam Equalizer System)
Replacement
Rotary Superstructures
Click to Enlarge
For
Twin-Post Rotary Low-Pressure
In-Ground
Lifts that need complete new Arms,
Superstructures
& Flip-Up Style Adapters.
$2349.00
Delivered
FJ5208
for Rectangular Piston Bolt Pattern
or
FJ5207
for Square Piston Bolt Pattern
Flip-Up
Adapter Kit For ROTARY
Includes High Step, Low Step and Pin that holds them together. Two
different attaching swivel pins included for use with either surface lift arms
or
in-ground lift arm sleeves.
One
Kit $59.95 Delivered
FOUR KITS
$225.00 Delivered
ROTARY Replacement EqualizerCover Plate & Repair Parts
for
DTO Model Two-Post Low-Pressure In-Ground Lifts
SAVE THAT
Rotary 2-POST
Low-pressure In-ground Lift!
Click
to enlarge image
#4 Steel Cover Plate For Floor
$98.00
Delivered
#2 Equalizer "I"
Beam Frame $1198.00
Delivered
WITH SLIDER BLOCKS
#
2
Equalizer "I"
Beam Frame $1129.00
Delivered
WITH ROLLER BEARINGS
#5
Safety Latch Repair Kit $189.00Delivered
Includes
2 latches and pins for welding to "I" beam
"Delivered"
= "Free Shipping"
SAVE THAT
Rotary 2-POST
Low-pressure In-ground Lift!
DIRT
FILLING YOUR ROTARY 2-POST LIFTS EQUALIZER
BOX SO IT WON'T
LOWER ALL THE WAY?
ROTARY DTO
Style two post in-ground lifts are one of the most dependable
lifts ever
made, but they had one major flaw and that was the fact that the
equalizer box
the "I" beam equalizer lowered into would rust through
allowing
dirt and back-fill to cause the lift to not lower
completely.
Up until the time this kit was created, the only thing
you could do was to
excavate the equalizer box and install a new one at
a cost of about three thousand
dollars, sometimes even more depending on
who was doing the job!
Now you
can solve the problem of equalizer box decay without
breaking out your floor or doing any
excavating or concrete work!
If
you've got about 3 hours and want to save thousands of dollars
in Rotary
Equalizer Box replacement costs, or the cost of a new lift,
all you'll need then is this
kit to fix the problem...
This heavy duty
kit comes complete with rack
bars, shaft, pinion gears, support housing,
cover plate, anchor bolts, hardware
kit and simple installation instructions.
Everything you need (except the
hand tools) to do it!
Kit is
$1489.00 Delivered!
Measure the width of your
Rotary
Equalizer Box the "I" Beam Equalizer
raises
in
and out of, they are either 4 inches or 4-3/4 inches wide.
Equalizer Kit
for 4" Wide Equalizer Box
For
4 inch wide box
Equalizer Kitfor
4-3/4" Wide Equalizer Box
For
4-3/4 inch wide box
Safety
Leg / Non-Rotators
For Single Post
In-Ground Automotive Lifts
and Heavy Duty Fore & Aft Truck and Bus Lifts.
Single
Post in-Ground Vehicle Lifts:
Safety Legs actually serve a dual purpose.
They not only act as a
safety mechanism, but they also prevent the lift from being able
to
Turn or Rotate. (Ever see someone turn a small car around on a
lift while it's up in the air?)
Commonly called "Non-Rotators" they
keep the pins on the bottom of the
lift piston (plunger) from lining
up with the slots in the cylinder casing.
(Pistons are removed
from the casings by lining up the pins with the slots, and it's
not
too safe to have that happen with a car all the way up in the air.)
Fore
& Aft Truck & Bus Lifts:
Often
they are just missing on some fore & aft truck lifts....
It could save
you or at least your
toolbox, oil drain or other equipment if a truck lift
decides to come
down on it's own. Lifts can drop as quickly as the oil can be
sprayed
from an oil supply hose that's feeding the front cylinder if
it pops.
Pit
located feed hoses can be up to 1 inch I.D. on older Truck & Bus
lifts.
Many
times hoses are left hanging in a polluted mix of oil and water
eventually weakening the hose causing it to fail. Unfortunately this
has a way of happening when there is a heavy load on the front
cylinder. You
can't see the feed hose because they are located under the steel pit
cover plates.
(Fore
& Aft lifts should be inspected for preventive maintenance twice a
year to
Lift
lock mechanism rebuild kit, has most hardware needed to
replace worn or missing parts from Weaver 2-post EC881 and
some other in-ground models that have the locking style
pillow blocks. NOTE!
Must have locking style pillow blocks on your lift to
install this kit, it will not work with non-locking style
pillow blocks.
Measure
the distance between the two piston "centers" to find the correct size for your
lift.
Kit for 57.5 inch
wide piston centers NON-LOCKING
WITH
RECTANGULAR RACK BARS
$1525.00
Delivered
Order
directly from our website, or by calling
630-678-9010 between 9AM & 5PM
(Central-Time) Mon - Fri. If you happen to get the "phone
lines are busy message" please leave your phone number, as well as
a detailed message and we'll call you back with the information you
requested ASAP.
Weaver
Lift
Parts
Parts for
Weaver EC-100, 102, 103, 105, 106, 202, 203 series
Fore & Aft Lifts.
Front
Piston Hydro Hose
Weaver (or
other) 3/4" NPT
$89.00 Delivered
3/4"
diameter Hydro Hose 9815
STOP Those Leaky
In-Floor Oil Valves! Valve Core rebuild kits include new core, seal, gasket,
boot and roll pin.
Aluminum Control Core
Kit controls oil to each cylinder
with short stem
(5-1/2
total length, 3" stem)
$56.00 Delivered
Aluminum Control Core
Kit controls oil to each cylinder
with
long stem (7-1/2 total length, 5" stem)
$62.00 Delivered
Core with long stem
Aluminum Directional Core Kit
directs oil to either cylinder
with short stem
(5-1/2 total length, 3" stem)
$98.00 Delivered
with short stem
Aluminum Directional Core Kit
directs oil to either cylinder
with long stem
(7-1/2 total length, 5" stem)
$188.00 Delivered
with long stem
BRASS
AVAILABLE TOO! Call 630-678-9010
Trolley Axles, Ratchet Assemblies
& Chain, Hoses, Tanks, Safety Legs, Saddles & Adapters... Contact us with your requirements and we will
give you a parts quote...
Weaver 7-1/2
Diameter Seal kit for Fore &
Aft Cylinders
Only.
(They are different
from the kits for a side by side twin post lift.)
Each
$109.00 Delivered
7-1/2 inch Packing Expander
(Spring
Loaded to apply pressure on packing) Each
$159.00
Weaver 10-5/8
Diameter seal kit for Fore & Aft Cylinders
(They are different
from the kits for a single post lift)
Each $135.00 Delivered
Kits are complete with installation instructions
10-5/8
Packing Expander
Located Under Seals
(Spring
Loaded to apply pressure on packing)
Each $189.00
Delivered
If
you don't see what you're looking for... Contact us. We've got them all!
This seal kit fits all
7.5
Globe cylinders.
Includes: Wiper, Seal, Complete Set of Assorted Gaskets
(You'll have a few
left over) and Installation
Instructions.
Each Kit
$159.00 Delivered
Lift Seal Kit for
Globe
8-1/2 inch
diameter piston
This seal kit fits all 8.5
Globe cylinders.
Includes: Wiper, Seal, Complete Set of Assorted Gaskets (You'll have a few
left over) and Installation
Instructions. Seal has ribbed
rubber style expanding method instead of steel spring.
Each Kit
$159.00 Delivered
These kits will replace the seal on 1
cylinder
Original
Spring style kit available for 8.5 in diameter
piston
Includes: Wiper, Seal,
Spring, Complete Set of Assorted Gaskets (You'll have a few left over) and
Installation
Instructions. Uses spring for expander instead of "rubber
ribbed" style expanding
method. (Spring style may be a little easier to
install than the ribbed style is.)
Each
Kit $169.00 Delivered
Globe 8-1/2
Cylinder NEW WIPER COVER/GLAND RING
NOTE:
UPPER BEARING NOT INCLUDED
$248.00
Delivered
The
NEW Style D.U.S.L. 10-5\8 Diameter Replaceable Upper Bearing Kit
Used
on the New FS10 GLOBE Single Post Lift Kits link
are
available to upgrade your older Globe lift that may have upper bearing
wear
that
may be causing "Piston Wobble" after 20+ years of service.
You
get the New Style A.T.F. (Adjust-To-Fit) Upper Bearing and the new style
"Leak-Sealer" Packing Kit
$798.00
Delivered Call for more info or to order one 630-678-9010
Globe10-5/8 Cylinder View (Gland
has Twelve bolts and 12 point bolt heads are common, but sometimes
they used "Allen Style " hex head bolts instead)
OIL PLUG AND DIPSTICK For Globe
Semi-Hydraulic
Lifts with PLUG in the center of the top of the piston.
(2.59 inch diameter thread) Gasket
Included
#10 & #11 in reference drawing
above
$85.00 Delivered
This
Original Globe Seal Kit fits all 10-5/8 Cylinders
Includes: Wiper, Seal, Complete Set of Assorted Gaskets and Installation
Instructions.
Seal has ribbed rubber style expanding method instead of steel
spring.
$164.00 Delivered
(These kits will replace the seal on 1 cylinder)
Original
10-5/8 Spring style Seal Kit
For 10-5/8 inch diameter Globe
Piston
Includes: Wiper, Seal,
Spring, Complete Set of Assorted Gaskets (You'll have a few left over) and Installation
Instructions. Uses spring for expander instead of "rubber ribbed"
style expanding method. (Spring style may be a little easier for you to install than
the ribbed style is.)
$174.00
Delivered
Globe 10-5/8
Cylinder NEW WIPER COVER/GLAND RING
NOTE:
UPPER BEARING NOT INCLUDED
$265.00
Delivered
35054
Globe
12-5/8 Seal Kit
Includes: Wiper, Seal, Complete Set of Assorted Gaskets and Installation
Instructions.
Seal has ribbed rubber style expanding method instead of steel
spring.
$268.00 Delivered
(These kits will replace the seal on 1 cylinder)
Globe
12-5/8
Spring style Seal Kit
for
12-5/8 inch diameter Globe Cylinder
Includes: Wiper, Seal,
Spring, Complete Set of Assorted Gaskets (You'll have a few left over) and Installation
Instructions. Uses spring for expander instead of "rubber ribbed"
style expanding method. (Spring style may be a little easier for you to install than
the ribbed style is.)
All Globe Equalizer Parts Available To Ship
Today!
(Contact us for
a quote on auto-locking equalizer mechanisms)
Some Parts in above image
listed below:
Globe
Rack Bar Manual Lock Mechanism
- You get TWO LOCKING BLOCKS that
slide onto the rack bar at any point and the lift will not lower past that
point
$185.00 Per Kit Delivered
Rack Bar (Manual
Locking)
$459.00 Each Delivered
9410 weighs 43 lbs
Rack Bar Auto (4 position) Locking
$459.00 Each Delivered
9409 weighs 43 lbs
Pinion Gear with Keyway$115.00 Each Delivered
(Globe Gears have 18 Teeth On Them)
NON-LOCKING (left or right) Equalizer Housing
Bracket $212.00 EachDelivered
LOCKING (Left Hand) Equalizer
Gear Housing
Bracket $326.00 EachDeliveredHas locking parts included with it
LOCKING (Right
Hand) Equalizer Housing
Bracket $326.00
Each DeliveredHas locking parts included with it
Both
Left & Right LOCKING Equalizer Gear Housings
$625.00
Delivered (Save $27.00 instead of buying
them separately)
Locking
Hardware
Kit Complete For One Housing Bracket, will
rebuild one locking mechanism on one housing. (Must be locking type equalizer
housing bracket to begin with, won't convert non-locking type)
One
kit $125.00 Delivered
GLOBE Equalizer Shafts
IMPORTANT!
Measure the distance
between the piston
centers to determine the length of the correct
equalizer
shaft, the shaft sizes below reflect the distance between the piston centers,
not necessarily the length of the shaft itself.
36 inch
piston centers equalizer shaft $159.00
Each Delivered
36 inch
piston centers LOCKING equalizer shaft $159.00
Each Delivered
Use locking shafts
with locking housing brackets
39 inch
piston centers equalizer shaft $198.00
Each Delivered
39 inch
piston centers LOCKING equalizer shaft $198.00
Each Delivered
42 inch
piston centers equalizer shaft $198.00
Each Delivered
42 inch piston centers LOCKING equalizer shaft $198.00
Each Delivered
Use locking shafts
with locking housing brackets
46 inch
piston centers equalizer shaft $212.00
Each Delivered
46 inch piston centers LOCKING equalizer shaft $212.00
Each Delivered
57-1/2 inch piston centers equalizer
shaft $225.00 Each Delivered
57-1/2 inch
piston centers LOCKING equalizer
shaft $225.00 Each Delivered
Use locking shafts
with locking housing brackets
83-1/2 inch piston centers equalizer
shaft $239.00 Each Delivered
83-1/2 inch
piston centers LOCKING equalizer
shaft $239.00 Each Delivered
Call for 88 inch piston centers equalizer shaft
Complete
Manual-Locking Equalizer Kits
For Globe In-Ground lifts
Include 2 rack
bars, 2 pinion gears, 2 gear housings,
1 shaft and hardware kit.
26-1/2 inch piston centers complete equalizer
kit $1200.00 Delivered
29-1/2 inch piston centers complete equalizer
kit $1200.00 Delivered
36 inch piston centers complete equalizer
kit $1200.00 Delivered
39 inch piston centers complete equalizer
kit $1200.00 Delivered
42 inch piston centers complete equalizer kit $998.00
Delivered
57-1/2 inch piston centers complete equalizer kit $1249.00
83-1/2 inch piston centers complete equalizer kit $1249.00
88 inch piston centers complete equalizer kit $1259.00
Locking style kits available
too, Call Us!
Replacement
Adapters and Pads available for all lifts, if you can't find them following this link,
just give us a call with the lift
brand name and your lifting requirements. LINK
Is
Your In-Ground Lift Chattering?
Help stop
the problem by adding "Metholardate"
to the oil
Lift
Oil Additive
Metholardate adds lubricity
to the hydraulic oi
l and
"Sticks" to the internal metal surfaces protecting them. New seals tend to provide more sealing surface which can
cause the lift to hang-up on the way down, especially if it doesn't have a
load on it. It is recommended with every
in-ground lift seal change and anytime the lift is chattering.
1 Qt. Can 9960-25 $33.00
Delivered
1 Gallon Can 9960-01
$89.00
Delivered
Order
directly from our website, or by calling 630-678-9010 between 9AM & 5PM (Central-Time) Mon - Fri. If you
happen to get the "phone lines are busy message" please leave your
phone number, as well as a detailed message and we'll call you back with the
information you requested ASAP.
/Manitowoc
In-Ground Lift Seal Kits
Authorized
Manitowoc Warranty Service Center Genuine Gilbarco / Manitowoc Parts
Complete 40 inch piston
center equalizer kit $1279.00 Delivered
Complete 57.5 inch piston center equalizer kit
1339.00 Delivered
Complete 89 inch piston center equalizer kit
$1359.00 Delivered
Measure the distance
between the pistons centers to determine the length of the equalizer shaft.
"Locking
style equalizer kits" available too, just contact us for a fast quote...
Order
directly from our website, or by calling 630-678-9010 between 9AM & 5PM (Central-Time) Mon - Fri. If you
happen to get the "phone lines are busy message" please leave your
phone number, as well as a detailed message and we'll call you back with the
information you requested ASAP.
Joyce
In-Ground Lift Seal Kits
Don't
Buy Second Rate Seal Kits... Get The Best, Right Here!
For all 7-1/2 in. diameter pistons $119.00 Delivered
Universal Kit "Leak Sealer" helps seal worn
pistons
For all 8-1/2 in. diameter pistons $148.00
Delivered
pistons
For all 10-1/2 in. diameter pistons $129.00 Delivered
Universal Kit "Leak Sealer" helps seal worn
pistons
For all 12-1/2 in. diameter pistons $198.00 Delivered
X00113 Genuine ALM Part
A00082-16 STRAIGHT 5/32 push-in hose connector
A00082-09 ELBOW 5/32 push-in hose connection with 1/8 NPT
A00082-15 RUNNING "T" 5/32 push-in hose
connections with 1/8 NPT
Mounting Hardware Included
36025 
NOTE:
These items must be made... allow 15-20 days for delivery.
Air Exhaust Muffler
Genuine
Rotary Part
2-3/8
Outside Diameter Pipe
